Reasons Your Fiat 500 Key Fob Won’t Work
A key fob for the fiat ducato key fob replacement 500 is a convenient way to unlock the doors and start the car. However, there are many reasons why the fob won’t be functioning. These include a dead battery, damage to the receiver module, water issues, and interference.
This listing is for a NEW replacement key for fiat ducato van fiat 500x key Flip Key Remote – similar to the Ilco brand that needs to be programmed professionally by a local automotive locksmith (click here for Locksmith Search). It comes with lock, unlock and trunk buttons.
Dead Coin Battery
The most common reason your 500 key fob won’t function is an inactive battery. Key fobs of today have only a limited range of operation and must be within only a few inches from the vehicle in order to function. If you are not within your vehicle, and you press the keyfob button it will not respond and display the message “Key Fob Not Detected”.
If this happens, replace the battery on your coin cell (Part number CR2032) with a fresh one from a reliable brand such as Panasonic, Duracell, or Energizer. They can be found in your local hardware store, or online.
After you’ve replaced the battery in the coin cell You can test it by standing in front of your fiat scudo key replacement 500 and pressing the buttons. The parking lights should flash and the key fob will operate the lock and unlock switch.
If the key fob won’t work after replacing the battery, it might have water damage that prevents it from communicating with the receiver module in your car. Water damage can happen through a variety of methods, including the simple splash or submerging the key fob saltwater at the beach. If you think your fob was exposed to water, put it in a bag of rice to draw out the moisture. If this doesn’t work the fob might need to be reprogrammed by an experienced locksmith or dealer.
Water Damage
Water damage can happen if you submerge the fob in the ocean or wash it in a washer. Saltwater can cause the circuit board to short and eventually die. In the event that you let your fob get wet, it’s not a good idea but if you drop it into a cup of water or don’t remember to take it out of your pocket before you run the washer, don’t give up hope.
First remove the battery from the fob. Clean the electronic chip using isopropyl ethanol or a similar product and then dry it thoroughly before replacing the battery. Test the fob next to determine if it’s working. If the key does not work, it might need to be programmed again. This is usually handled by a dealer or professional auto locksmith.
If your key is older and has not been programmed to work with your vehicle, you will need to replace it completely. A professional locksmith in the automotive industry will be able to complete this process. The locksmith needs to cut the key to match the ignition of your car. They’ll also need to program the fob into your vehicle’s system. This is a fast and affordable process that is usually completed the same day.
Receiver Module Issues
Your 500 key fob may stop working because it is out of range. The remote’s range is of 30 feet, which means if you are too far from your vehicle it won’t respond to your commands. You can remedy this by moving your remote closer to your car until it responds.
If your fob does not work after replacing the battery inside the coin, which is also called a “button”, “watch” or “button” or “button”, it could be a problem with the circuit board inside. Reprogramming the fob is usually the solution to this issue. You can find the procedure for most vehicles on YouTube or in the owner’s manual.
It could be necessary to replace the clips made of metal that hold the coin batteries in place. If they loose tension it can prevent the battery from sitting properly, and this will result in the malfunction of your remote.
In rare cases the fob could be disconnected from your vehicle due to software or hardware issues. This could be a huge trouble, but you could usually fix it by visiting an auto locksmith to reprogram your fob for you. In some instances they may have to reinstall the program in your body control module as well.
Interference
In addition to a dead battery on a coin The key fob might not be receiving or transmitting the signal due to interference. This can happen when the key fob is located near radio transmitters (cell phones, radar detectors) or another source of electromagnetic radiation. Other reasons why the key fob may not function may be a lack of connection to the buttons, damage to the internal chip, or water damage.
If the key fob has stopped working one day suddenly or after trying everything you can at home to resolve it e.g. You could have a malfunctioning 500 receiver module in the event that you’ve tried replacing the battery, reprogramming it, or using an alternative key fiat fob. The receiver module, which is located under the dashboard, is able to pick up radio frequency signals from your key fob. It transforms the signals into electronic commands that are then interpreted by the vehicle.
There’s a quick and easy way to reset the 500’s in-board system including the keyfob. Disconnect the 12 volt battery for approximately 15 minutes by removing the negative cable first then the positive cable. Then, reconnect the battery. This will eliminate any remaining electricity, and restart the computer of your car. This can help get your key fob to work again. If the issue continues you should seek out an expert technician. They’ll be able to determine the root of your problems.